Aniline Leather Wax Pull Up Protein Stain Remover Kit AW5.ps

Aniline Leather Wax Pull-up Protein Stain Remover Kit AW5.ps by Leather Doctor removes body discharge, milk, cream, vomit, and all other protein-based stains.

Protein-based stains tend to coagulate and become part of the leather making removal more difficult and requiring a specialty product.
 
Tips:

The dry surface deposit is removed with Horsehair Brush 1, Leather Eraser 4, and Bamboo skewers and wiped clean free of residue.
Note that the topcoat in most cases will be damaged and need to be refinished after the stain is removed.
There might be a little discoloration and this side effect is rectified by using Hydrator 3.3 to redistribute the dormant aniline dyestuff from the structure thickness to the surface.
The entire panel has to be done without allowing any dry space, otherwise, line rings and marks will be another repeat to disperse them. Understanding that minor damages are inevitable and required to make good after removal, we can proceed with the wet cleaning process.
 
The holistic remover and conditioning system comprises these 6 steps:

Step 1 Protein Stain Remover:
Cleaner 9.9 is specially formulated to break down any protein stain, that comes from a living animal or person. In a holistic remover, it has to be rinsed with Acidifier 2.0.

Step 2 pH Balancing Rinse:
Acidifier 2.0 is a leather pH stabilizer, that is used to rinse and neutralize, remaining residues, to the leather, desired neutral pH of 3 - 5, and simultaneously, ensure that the leather, retains its healthy squeaky feel, with a testing wet finger.

Step 3 Hydration:
Hydrator 3.3 relaxes stiff leathers and reduces surface tension before fatliquoring (fat and oil) replenishing.

Step 4 Fatliquoring:
Fatliquor 5.0 rejuvenates the leather structure, for softness and strength, to suppleness when dry.

Step 5 Wax Pull-up Conditioning:
Pull-Up 8.6 rejuvenates the internal structural cross-section wax pull-up effect and slowly coagulates as it dries to a cloudy waxy coating, on the surface, to be heat activated, into the desired glossy characteristics.

Step 6 Non-Stick Rub-Resistant Protection:
Protector D imparts a non-stick protection, to shield the surface, against sticky soiling, besides healing and concealing lightening scuff, and abrasion marks.

Instructions:

The concentrate in the bottle has to be mixed with distilled water accordingly before use.
 
Step 1 - How to Work with Leather Protein Cleaner 9.9?
Deep removal into the leather structure to break the stain down will need the help of a smooth spatula like a spoon, agitating it to break up the coagulating stain. Inevitably the topcoat is the sacrifice for the moment to reach deep to the bottom of the stain. It will need be refinished with Aniline Gloss Topoat 76 later as necessary. There might be a little discoloration and this side effect is rectified by using Hydrator 3.3 to redistribute the dormant aniline dyestuff from the structure thickness to the surface. And the entire panel has to be done without allowing any dry space, otherwise, line rings and marks will need another repeat to disperse them. If this expectation is understood, we can proceed with the wet cleaning. 
1* Inspect and remove all caked and surface with Horsehair Brush 1, Leather Eraser 4, bamboo skewers and wipe clean free of residue. deposits before application.
2* Apply, agitate with an appropriate tool, extract with a towel, and repeat until the stain is removed.
 
Step 2 - How to Work with Leather Acidifier 2.0?
1* Apply directly and agitate with a leather brush and towel extract.
2* Apply dwell and extract with a dry absorbent towel.
3* Test with a finger to have a healthy squeaky feel.
 
Step 3 - How to Work with Leather Hydrator 3.3?
1* Apply and brush into the leather for an even darkening absorption to the entire panel without a dry edge.
2* Towel extract until towel shows clean and is ready for immediate Fatliquoring.
 
Step 4 - How to Work with Leather Fatliquor 5.0?
1* Apply and distribute with appropriate brushes or pads until the thickness of the leather is saturated following the path of Hydrator 3.3 without a dry edge.
2* Repeat each time water contents evaporate leaving behind only the fat and oil content.
3* Sticky residue is further driven into the leather structure or rinsed off until surface milky fat and oil turn clear with Hydrator 3.3.
4* Allow natural drying for extra softness.
5* Suppleness of leathers is further staked, massaged, and flexed accordingly with a little wetting back with Hydrator 3.3 until dry.
 
Step 5 - How to Work with Aniline Leather Wax Pull-Up 8.6?
1* Apply and spread with a horsehair brush evenly to produce a darkening effect.
2* Allow up to 8 hours of natural drying time or until cloudy wax crystalline is apparent.
3* Activate the wax deposit with a heat blower or hairdryer to a natural gloss.

Step 6 - How to Work with Pull-Up Leather Protector D?

1* Apply and spread evenly with a brush or pad.

2* The leather is ready to use when dry.